Array Support Library for DotHill R/Evo Series Arrays (Active/Active) on Veritas Volume Manager (tm) 5.0 and later for Solaris Sparc
| Article:TECH53292 | | | Created: 2007-01-28 | | | Updated: 2010-01-19 | | | Article URL http://www.symantec.com/docs/TECH53292 |
Problem
Array Support Library for DotHill R/Evo Series Arrays (Active/Active) on Veritas Volume Manager (tm) 5.0 and later for Solaris Sparc
Solution
This TechFile provides information about the Array Support
Library (ASL) for DotHill R/Evo Series Arrays on Veritas Volume Manager 5.0 and
later for Solaris Sparc
For general information about ASLs, see TechNote 249446 http://support.veritas.com/docs/249446
For general information about ASLs, see TechNote 249446 http://support.veritas.com/docs/249446
Package
Name: VRTSDotHill
Package
Version: 5.0,REV=08.31.2007.10.33
Supported
versions of Veritas Volume Manager: 5.0 and later
Supported
Arrays: DotHill R/Evo Series Arrays (Active/Active)
Installation Instructions:
Before adding any ASL package, ensure Veritas Volume Manager is installed and enabled
# vxdctl mode
mode: enabled
1. At the bottom of this TechFile, click on Download Now to download the ASL package in /tmp/ASL
# mkdir /tmp/ASL
# cd /tmp/ASL
2. After downloading VRTSDotHill-5.0-SunOS-v1.0_290839.tar.Z, verify the cksum of the file
# cksum VRTSDotHill-5.0-SunOS-v1.0_290839.tar.Z
3777702713 10252 VRTSDotHill-5.0-SunOS-v1.0_290839.tar.Z
3. Uncompress the file
# zcat VRTSDotHill-5.0-SunOS-v1.0_290839.tar.Z | tar xvf -
4. Install the ASL using pkgadd
# pkgadd -d . VRTSDotHill
5. Verify pkginfo
# pkginfo -l VRTSDotHill
PKGINST: VRTSDotHill
NAME: Array Support Library for DotHill Evo and FSC FibreCAT series Arrays
CATEGORY: system
ARCH: sparc
VERSION: 1.0,REV=08.31.2007.10.33
BASEDIR: /etc/vx
VENDOR: VERITAS Software
DESC: Array Support library for DotHill Evo and FSC FibreCAT series Arrays
PSTAMP: VERSION-1.0:20-June-2007
INSTDATE: Aug 31 2007 10:37
HOTLINE: 800-342-0652
EMAIL: support@veritas.com
STATUS: completely installed
FILES: 5 installed pathnames
3 directories
2 executables
27 blocks used (approx)
6. After executing vxdctl enable and vxconfigd -k, verify the output of the vxddladm listsupport command, as follows:
# vxddladm listsupport libname=libvxfsc.so
ATTR_NAME ATTR_VALUE
=======================================================================
LIBNAME libvxfsc.so
VID FSC, DotHill
PID FibreCAT_SX1, R/Evo 2730-2R, R/Evo 2530-2R
R/Evo 2330-2R, R/Evo 2130-2RX, R/Evo 2130-2J
ARRAY_TYPE A/A
ARRAY_NAME FSC-FibreCAT, DotHill-Evo
Attachments
|
|
Legacy ID
290839
Article URL http://www.symantec.com/docs/TECH53292
Terms of use for this information are found in Legal Notices
Thank you.