Vidéos d'aide de Screencast

VCS Attribute question

Created: 12 Sept 2012 | 9 comments

I need to set an attribute but I don't know which one I need.

When I do a switch sometimes I have resources hang for up to a minute, they don't fault they just hang. Is there a attribute that will continue to ping the resource every 2 second or so and say "offline" or "online"? It does seem to do this when it hangs but it may take a minute or two.

Discussion Filed Under:

Commentaires CommentairesAccéder au dernier commentaire

l'image des Paresh Bafna


There are Type level attributes that define online and offline monitor interval -
MonitorInterval - monitor interval when state of resource is online - typically 60 sec.
OfflineMonitorInterval - monitor interval when state of resource is offline - typically 300 sec.

Decreasing these intervals will schedule monitors for the resource more frequently. However this will also put more load on the system.

If you could provide more details like which resource is taking long to come online or report fault, any specific reason why the resource is faulting, what is you exact requirement we could suggest you better solution.

Thanks and Regards,
Paresh Bafna

Thanks and Regards,
Paresh Bafna

l'image des mhab11

The software that I am running fails to offline. It is the first item to offline. It appears that it will try 3 times then wait about 5 min then when it tries to offline again it says "o you are offline" and everything else offlines as it should.

This software is setup under general services and the AMF is as follows:


Monitor interval 60

Offline Monitor Interval 300

Registerretrylimit 3

The the Tolerance limit is set to 0

I am thinking that if I change the Monitor interval to 10 and the Offline Monitor Interval to 10 it should fix my problem by continually say, offline.

l'image des Paresh Bafna


You mentioned, your software fails to offline. Why exactly your software fail to offline?
We need more details about your setup like –
- What VCS resource you are using to monitor your software?
- VCS configuration snippet
- Without VCS how much time is taken by your software to completely offline?

If VCS resource monitoring your software is registered with AMF then AMF should provide instantaneous notification whenever software goes offline. This is the purpose of registering any VCS resource with AMF.

If you change MonitorInterval and OfflineMonitorInterval to 10 sec, monitor will be invoked every 10 sec. This will load your system with frequent monitor invocations. We can recommend any configuration change only after reviewing your existing configuration and understanding your software behavior.

Thanks and Regards,
Paresh Bafna

Thanks and Regards,
Paresh Bafna

l'image des mhab11

It appears that the resource signals for the offline, the application takes about 30 secs to offline but by then VCS doesnt see it anymore, almost like the MonitorInterval stopped working. After about 5 min or say 300 secs. VCS sees it offline and everything else goes down just fine.

It is a GenericService.

What is a snippet?

outside of VCA I can offline the software in about 30 secs.

I have AMF setup:

Mode 3 / MonitorInterval 60 / OfflineMonitorInterval 300 / RegisterRetryLimit 3

I was going to change this to:

Mode 3 / MonitorInterval 10 / OfflineMonitorInterval 10 / RegisterRetryLimit ? (should I set this to 0 or 10)

l'image des Paresh Bafna

Could you please let me know OS version you are on and VCS version you are using?

Thanks and Regards,
Paresh Bafna

Thanks and Regards,
Paresh Bafna

l'image des Paresh Bafna

I am not aware of exact behavior of AMF and VCS on Windows.

I would let Windows expert comment on this.

Thanks and Regards,
Paresh Bafna

l'image des mikebounds

This is what I believe should happen:

Offline entry point is called and this will stop the service.  When the offline entry point "thinks" the service stopped, the offline entry completes and the monitor entry point is called.  Problems can occur if the service is not stopped when the monitor entry point is called and this depends on how the offline entry point is determines the service is stopped.  I don't know how the code works for this particular resource type, but 3 main ways are:

  1. The command/API to stop the service used by the offline entry points does not return until the service has stopped, so offline entry point exits when command/API to stop the service exits.
  2. The code internally loops with the offline entry point to check when it is offline
  3. The code just waits a fix amount of time, say 10 seconds which is hard-coded or can be set by a resource attribute (as oppose to a resource type attribute)

Just looked at bundled agents guide and code does do 3 and the "wait" can be set by using "DelayAfterOffline" attribute for your GenericService resource (this is set on the resource, not the resource type/agent) which is 10 seconds by default, so you need to set this to 30 seconds or more.

What you are seeing at the moment is the offine entry point doesn't wait long enough and then the monitor entry point returns unknown (If the monitor entry point returned offline, then resource would be cleaned if OfflineWaitLimit is set to default of zero), so then I guess VCS then runs a monitor determined by the OfflineMonitorInterval.   


UK Symantec Consultant in VCS, GCO, SF, VVR, VxAT on Solaris, AIX, HP-ux, Linux & Windows

If this post has answered your question then please click on "Mark as solution" link below

l'image des amitsgupte

If this is a case where the actual service stop is taking more time than the Generic Service offline timeout, we would see errors\warnings (as below) in the eventviewer. 

"The service <name> did not stop within the specified timeout. Error = <err_code>",