Backdoor.Domwis - Removal

The following instructions pertain to all current and recent Symantec antivirus products, including the Symantec AntiVirus and Norton AntiVirus product lines.

1. Disable System Restore (Windows Me/XP).
2. Update the virus definitions.
3. Restart the computer in Safe mode or VGA mode.
4. Run a full system scan and delete all the files detected as Backdoor.Domwis.
5. Delete the value that was added to the registry.
6. Restart the computer in Normal mode.
   

For specific details on each of these steps, read the following instructions.

1. Disabling System Restore (Windows Me/XP)
If you are running Windows Me or Windows XP, we recommend that you temporarily turn off System Restore. Windows Me/XP uses this feature, which is enabled by default, to restore the files on your computer in case they become damaged. If a virus, worm, or Trojan infects a computer, System Restore may back up the virus, worm, or Trojan on the computer.

Windows prevents outside programs, including antivirus programs, from modifying System Restore. Therefore, antivirus programs or tools cannot remove threats in the System Restore folder. As a result, System Restore has the potential of restoring an infected file on your computer, even after you have cleaned the infected files from all the other locations.

Also, a virus scan may detect a threat in the System Restore folder even though you have removed the threat.

For instructions on how to turn off System Restore, read your Windows documentation, or one of the following articles:

• "How to disable or enable Windows Me System Restore"
• "How to turn off or turn on Windows XP System Restore"

Note: When you are completely finished with the removal procedure and are satisfied that the threat has been removed, re-enable System Restore by following the instructions in the aforementioned documents.

For additional information, and an alternative to disabling Windows Me System Restore, see the Microsoft Knowledge Base article, "Antivirus Tools Cannot Clean Infected Files in the _Restore Folder," Article ID: Q263455.

2. Updating the virus definitions
Symantec Security Response fully tests all the virus definitions for quality assurance before they are posted to our servers. There are two ways to obtain the most recent virus definitions:

• Running LiveUpdate, which is the easiest way to obtain virus definitions: These virus definitions are posted to the LiveUpdate servers once each week (usually on Wednesdays), unless there is a major virus outbreak. To determine whether definitions for this threat are available by LiveUpdate, refer to the Virus Definitions (LiveUpdate).
• Downloading the definitions using the Intelligent Updater: The Intelligent Updater virus definitions are posted on U.S. business days (Monday through Friday). You should download the definitions from the Symantec Security Response Web site and manually install them. To determine whether definitions for this threat are available by the Intelligent Updater, refer to the Virus Definitions (Intelligent Updater).
  
  The Intelligent Updater virus definitions are available: Read "How to update virus definition files using the Intelligent Updater" for detailed instructions.

3. To restart the computer in Safe mode or VGA mode
Shut down the computer and turn off the power. Wait for at least 30 seconds, and then restart the computer in Safe mode or VGA mode.

• For Windows 95, 98, Me, 2000, or XP users, restart the computer in Safe mode. For instructions, read the document, "How to start the computer in Safe Mode."
• For Windows NT 4 users, restart the computer in VGA mode.
  

4. Scanning for and deleting the infected files

1. Start your Symantec antivirus program and make sure that it is configured to scan all the files.
   • For Norton AntiVirus consumer products: Read the document, "How to configure Norton AntiVirus to scan all files."
   • For Symantec AntiVirus Enterprise products: Read the document, "How to verify that a Symantec Corporate antivirus product is set to scan all files."
2. Run a full system scan.
3. If any files are detected as infected with Trojan horse, write down the name and location of the file, and then click Delete. You will need this information in the following sections.

5. Deleting the value from the registry
WARNING: Symantec strongly recommends that you back up the registry before making any changes to it. Incorrect changes to the registry can result in permanent data loss or corrupted files. Modify the specified keys only. Read the document, "How to make a backup of the Windows registry," for instructions.

1. Click Start > Run.
2. Type regedit
   
   Then click OK.
   
   
3. Navigate to the key:
   
   HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\Run
   
   
4. Refer to the list of the infected files that you created while following the instructions in the previous section. In the right pane, look at the entries in the Name and Data columns.
   
   
5. If you find an entry that refers to a file detected as infected, select the entry, press Delete, and then click Yes to confirm.
   
   
6. On Windows 95/98/Me computers, navigate to and select the following key:
   
   HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\RunServices
   
   
7. Refer to the list of the infected files that you created while following the instructions in the previous section. In the right pane, look at the entries in the Name and Data columns.
   
   
8. If you find an entry that refers to a file detected as infected, select the entry, press Delete, and then click Yes to confirm.
   
   
9. Exit the Registry Editor.
   

6. Restarting the computer in Normal mode.

For instructions, read the section on returning to Normal mode in the document, "How to start the computer in Safe Mode."

Technical Details